Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: The Dam Method of End Pours *PIC*
By:Nick Schade - Guillemot Kayaks
Date: 1/29/2013, 11:10 am
In Response To: Re: The Dam Method of End Pours (Kurt Maurer)

1. What's the piece of wood you're holding as you drill the hole?

Just a jig to help align the drill for getting the hole straight and true. I drill in from both sides and meet in the middle. The jig shows the alignment and the tab tells me how far from the edge the hole needs to be.

2. What's the tool used in deck installation, some sort of tape dispenser?

Yes, a 1" metal tape dispenser. http://www.uline.com/Product/Detail/H-108/Tape-Dispensers-Hand-Held/1-Metal-Tape-Dispenser

I find the tape dispenser very helpful in pulling the tape tight as I align the joint. I can manipulate and pull the tape with one hand while I adjust the boat and press the tape down with the other hand. The dispenser has a cutter to allow easy, one handed cutting. I have found that the success of joining the deck and hull, especially when they are distorted, depends a lot on how tight I can pull the tape and how well I can stick it down and this dispenser allows me to pull the tape very tight without having to let go to find something to cut it with.

I use 3M 893 Strapping tape. It sticks well and comes off clean.

Messages In This Thread

Epoxy: Lightweight endpours
Matt Jakubek -- 1/27/2013, 5:42 pm
Re: Epoxy: Lightweight endpours
Dan Caouette (CSCWC) -- 1/28/2013, 6:20 am
Re: Epoxy: Lightweight endpours *PIC*
Kurt Maurer -- 1/28/2013, 7:06 pm
Re: Epoxy: Lightweight endpours
george jung -- 1/29/2013, 12:18 am
Re: Epoxy: Lightweight endpours
Jay Babina -- 1/29/2013, 8:32 am
Re: Epoxy: Lightweight endpours
Bill Hamm -- 1/30/2013, 2:12 am
The Dam Method of End Pours *PIC*
Nick Schade - Guillemot Kayaks -- 1/29/2013, 10:22 am
Re: The Dam Method of End Pours
Kurt Maurer -- 1/29/2013, 10:28 am
Re: The Dam Method of End Pours *PIC*
Nick Schade - Guillemot Kayaks -- 1/29/2013, 11:10 am
Re: The Dam Method of End Pours
JohnAbercrombie -- 1/29/2013, 12:07 pm
Re: The Dam Method of End Pours
Bill Hamm -- 1/30/2013, 2:17 am
Re: The Dam Method of End Pours
Jack Hawkins -- 1/31/2013, 10:53 am
Re: The Dam Method of End Pours
Bill Hamm -- 2/1/2013, 1:44 pm
Re: The Dam Method of End Pours
Jack Hawkins -- 2/1/2013, 3:10 pm
Re: The Dam Method of End Pours
Kurt Maurer -- 2/1/2013, 9:28 pm
Re: The Dam Method of End Pours *PIC*
Etienne Muller -- 2/2/2013, 4:03 am
Re: The Dam Method of End Pours
Bill Hamm -- 2/3/2013, 2:39 am
Re: The Dam Method of End Pours
george jung -- 2/3/2013, 11:59 am
Re: Pictures from Bill
ddaniels -- 2/3/2013, 5:44 am
Re: The Dam Method of End Pours
Bill Hamm -- 2/3/2013, 2:37 am
Re: The Dam Method of End Pours
ancient kayaker -- 2/3/2013, 4:53 pm
Re: The Dam Method of End Pours
george jung -- 2/3/2013, 7:12 pm
Re: The Dam Method of End Pours
Bill Hamm -- 2/4/2013, 12:12 am
Re: The Dam Method of End Pours
Jack Hawkins -- 2/4/2013, 9:36 am
Re: The Dam Method of End Pours
Bill Hamm -- 2/5/2013, 4:37 am
Re: The Dam Method of End Pours
Sean Dawe -- 1/31/2013, 10:19 am
Re: The Dam Method of End Pours
Dan Caouette (CSCWC) -- 1/31/2013, 6:23 pm
Re: Epoxy: Lightweight endpours
Al Edie -- 1/28/2013, 10:49 pm
Re: Epoxy: Lightweight endpours
Rob Macks/Laughing Loon CC&K -- 1/29/2013, 9:05 am
Re: Epoxy: Lightweight endpours
ancient kayaker -- 1/29/2013, 10:51 am
Re: Epoxy: Lightweight endpours
Bill Hamm -- 1/30/2013, 2:19 am
Re: Epoxy: Lightweight endpours
ancient kayaker -- 2/2/2013, 1:00 pm
Re: Epoxy: Lightweight endpours *PIC*
Nick Schade - Guillemot Kayaks -- 1/29/2013, 9:36 am
Re: Epoxy: Lightweight endpours
Kurt Maurer -- 1/29/2013, 10:15 am
Re: Epoxy: Lightweight endpours
Kevin -- 1/29/2013, 1:32 pm
Re: Epoxy: Lightweight endpours
Matt Jakubek -- 1/29/2013, 5:45 pm
Re: Epoxy: Lightweight endpours
Nick Schade - Guillemot Kayaks -- 1/29/2013, 6:44 pm
Re: Epoxy: Lightweight endpours
Jay Babina -- 1/31/2013, 8:05 am
Re: Epoxy: Lightweight endpours
Bill Hamm -- 1/30/2013, 2:23 am
Re: Epoxy: Lightweight endpours
Kurt Maurer -- 1/31/2013, 7:49 pm