Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Seat Dimensions *Pic*
By:Joe Greenley
Date: 11/20/2000, 9:20 pm
In Response To: Let's Try This Again :) S, N, & E (Spidey)

Hello Ken
Fitting seats, in many respects, is like fitting shoes - one size doesn't necessarily fit everyone - some need D and others need EEE - anyway, I have found a good generic size to be 16" deep with about 1/2" of material left at the low point - you will be amazed at how lowering the center of gravity just a slight amount translates into quite a bit more stability.
Because you are using 4" thick foam, the depression at your hips will need to be nearly vertical at the top. From looking at your picture I would say that you need to take out quite a bit more foam. I like to leave 2" of material at the front - you will need to round it over more at this point as well.
The depression should be about 16" wide.
Hope this helps.
Joe

Messages In This Thread

Can We Discuss Carved Minicell Seats? *Pic*
Spidey -- 11/19/2000, 10:04 pm
Re: Can We Discuss Carved Minicell Seats?
Kathy Garlinghouse -- 11/21/2000, 1:20 am
Re: Can We Discuss Carved Minicell Seats?
Spidey -- 11/21/2000, 11:42 pm
Re: Can We Discuss Carved Minicell Seats?
Larry C. -- 11/20/2000, 10:07 pm
Re: Can We Discuss Carved Minicell Seats?
Spidey -- 11/20/2000, 10:29 pm
Re: Can We Discuss Carved Minicell Seats?
Ken Rasmussen -- 11/21/2000, 12:50 am
Re: Can We Discuss Carved Minicell Seats?
Larry C. -- 11/21/2000, 12:17 pm
Re: Ken's article
Shawn Baker -- 11/21/2000, 8:58 pm
Re: Seat Shape *Pic*
Shawn Baker -- 11/20/2000, 2:58 pm
Re: Shawn + Nick
Spidey -- 11/20/2000, 7:46 pm
Re: Sounds like you've got it.
Shawn Baker -- 11/21/2000, 11:16 am
Re: Sounds like you've got it.
Spidey -- 11/21/2000, 12:30 pm
Let's Try This Again :) S, N, & E
Spidey -- 11/20/2000, 8:06 pm
Re: Let's Try This Again :) S, N, & E
Nick Schade - Guillemot Kayaks -- 11/21/2000, 10:21 am
Re: Seat Dimensions *Pic*
Joe Greenley -- 11/20/2000, 9:20 pm
Re: Seat Dimensions
Spidey -- 11/20/2000, 9:49 pm
Re: Seat shape
Mike Hanks -- 11/20/2000, 8:43 pm
Re: Seat shape
Spidey -- 11/20/2000, 10:04 pm
Re: Seat shape
Richard Boyle -- 11/20/2000, 10:38 pm
Re: Seat shape
Spidey -- 11/20/2000, 11:04 pm
Re: Seat Shape
Nick Schade - Guillemot Kayaks -- 11/20/2000, 5:00 pm
Re: Seat Shape
eric schade (shearwater boats) -- 11/20/2000, 6:05 pm
Re: Wedge
Shawn Baker -- 11/20/2000, 5:56 pm
Me too!
Kent LeBoutillier -- 11/21/2000, 6:20 am
You can cover it in lycra.
.tim -- 11/20/2000, 1:01 pm
Re: You can cover it in lycra.
Spidey -- 11/20/2000, 8:13 pm
Burn it! ; )
Jerry Siegel -- 11/20/2000, 11:28 am
Re: I Did! :)
Spidey -- 11/20/2000, 1:40 pm
Can you sand it and coat again?
Brian Nystrom -- 11/21/2000, 12:45 pm
Re: Can you sand it and coat again?
Spidey -- 11/21/2000, 12:57 pm
Re: Can you sand it and coat again?
Jim Goecks -- 11/21/2000, 1:45 pm
Re: Burn it! ; )
Spidey -- 11/20/2000, 12:09 pm
Re: Can We Discuss Carved Minicell Seats?
Chris Casazza -- 11/20/2000, 11:19 am
Re: Can We Discuss Carved Minicell Seats?
Spidey -- 11/20/2000, 12:00 pm
Another thought on fiberglass lay-up
Jim Eisenmenger -- 11/20/2000, 4:51 pm
Re: Another thought on fiberglass lay-up
Spidey -- 11/20/2000, 10:14 pm
Re: Another thought on fiberglass lay-up
peter czerpak -- 11/21/2000, 8:28 am
Re: Another thought on fiberglass lay-up
Jim Eisenmenger -- 11/21/2000, 8:03 am
Re: Can We Discuss Carved Minicell Seats?
Chris Casazza -- 11/20/2000, 12:08 pm
Re: spray-on rubber coating
Dave E -- 11/20/2000, 10:22 am
Re: spray-on rubber coating
Spidey -- 11/20/2000, 11:46 am
Re: Can We Discuss Carved Minicell Seats?
Gini L. -- 11/19/2000, 11:44 pm
Re: Can We Discuss Carved Minicell Seats?
Spidey -- 11/20/2000, 12:09 am
Re: Can We Discuss Carved Minicell Seats?
Nick Schade - Guillemot Kayaks -- 11/20/2000, 9:39 am
Re: Can We Discuss Carved Minicell Seats?
Gini L. -- 11/20/2000, 10:58 pm
Re: Can We Discuss Carved Minicell Seats?
Spidey -- 11/20/2000, 1:32 pm
Vinyl?
Tom Tieman -- 11/20/2000, 6:24 pm
Re: Can We Discuss Carved Minicell Seats?
Grant Glazer -- 11/20/2000, 12:32 pm
Re: Can We Discuss Carved Minicell Seats?
John Monfoe -- 11/20/2000, 4:24 am
Re: Buoyancy
Shawn Baker -- 11/20/2000, 3:07 pm