Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Launching: Sea Flea
By:Brad Shook
Date: 6/27/2008, 1:29 pm
In Response To: Launching: Sea Flea *LINK* *Pic* (Pawistik)

Awesome!! Is the other boat in the photo a Guillemot?

: Hi Everyone,
: We launched the Yost Sea Flea 11 kayak that I built for my daughters nearly
: two weeks ago on a Saturday afternoon. The launch was a hurried affair as
: some weather was rolling in and the rain started while the second daughter
: had her turn. The next day we took it out for a more extensive run. Both
: girls had a lot of fun in the kayak.

: The kayak is the 11 foot version of the Sea Flea:
: http://yostwerks.com/SeaFlea3.html

: I constructed it with a wood frame, using scarfed cedar stringers and
: 1/2" plywood cross sections (stations). I coated the entire frame in
: epoxy, and painted the visible portions of the frame (and some extra) and
: cockpit yellow using Tremclad paint (aka Rustoleum). I picked that
: particular paint because I was shopping at a hardware store with limited
: selection and priming wasn't required. The kayak was skinned with 18 ounce
: PVC fabric purchased locally (Denham Awning Makers). The colours and
: designs used were selected by my daughters. I tried to include them as
: much as I could through the build. Of course this wasn't really very much
: and sometimes was insignificant things (holding something for me that
: didn't absolutely need holding) but they really enjoyed being part of it
: and are very proud of the boat they built. The cartoon orca on the deck
: was done using scrap pieces of PVC fabric, thrown in when I bought the
: fabric for the rest of the kayak.

: I built fore & aft flotation chambers using the instructions on Tom
: Yost's web site. http://yostwerks.com/FloatbagA.html

: A block of minicell foam was cut to fit tightly between the gunwale stringers
: as a foot brace. It's quite secure like that and when her legs are longer
: if it needs to move I can trim it and move it forward.

: The outrigger is similar to that designed in the Cunningham SOF kayak
: building book. It uses boat bumpers as floats with the floats being held
: in place by bungee and a webbing strap. I also added small wood pieces to
: the underside of the cross piece to help keep the floats in the right
: spot. I did this because initially I was only going to use the bungee, but
: decided it need something extra so added the webbing around the float

: The paddle that I made to go with the kayak was constructed of a cedar shaft
: (left over wood from making the stringers) with 1/8" birch plywood
: blades. The shaft is 7/8 x 1" and the total paddle length is about
: 55". The blades were drawn out to what looked about right and are
: symmetrical with a curved power face. The blades were painted, each
: daughter putting her own special touch on one of the blades. The blade
: painting was done before attachment to the shaft. The blades were edged
: with a 14 gauge bare copper wire for protection (tacked in place initially
: with crazy glue then held permanently with epoxy). The blades were covered
: on the power face with 1 layer of 6 ounce glass (I planned on using 4
: ounce, but forgot where I put it for a few hours).

: As usual, I have kept a blog of the progress. The link at the bottom will
: take you to all posts pertaining to the Sea Flea build (or use the label
: "kid kayak").

: The launch write-up and a few photos can be found here:
: http://pawistik.blogspot.com/2008/06/launch-of-sea-flea.html

: Many thanks to Tom Yost for the design and making the plans available to the
: community. Your efforts are greatly appreciated!

: Cheers,
: Bryan Sarauer

Messages In This Thread

Launching: Sea Flea *LINK* *Pic*
Pawistik -- 6/27/2008, 1:46 am
Re: Launching: Sea Flea
Sean -- 6/29/2008, 9:56 am
Re: Launching: Sea Flea
Tom Yost -- 6/28/2008, 11:31 am
Re: Launching: Sea Flea *LINK* *Pic*
Pawistik -- 6/27/2008, 2:23 pm
Re: Launching: Sea Flea *LINK*
Don T -- 6/27/2008, 11:36 pm
Re: Launching: Sea Flea
Pawistik -- 6/30/2008, 1:10 pm
Re: Launching: Sea Flea
Sean -- 6/30/2008, 8:28 pm
Re: Launching: Sea Flea *LINK*
Pawistik -- 7/2/2008, 3:34 pm
Re: Launching: Sea Flea
Sean -- 7/3/2008, 9:17 pm
Re: Launching: Sea Flea
Doug Smith -- 6/27/2008, 1:46 pm
Re: Launching: Sea Flea
Brad Shook -- 6/27/2008, 1:29 pm
Re: Launching: Sea Flea *LINK* *Pic*
Pawistik -- 6/27/2008, 2:09 pm
Re: Launching: Sea Flea
Michael McCluskey -- 6/27/2008, 5:52 pm
Re: Launching: Sea Flea
Pawistik -- 6/27/2008, 6:37 pm
Re: Launching: Sea Flea
Bill Hamm -- 6/27/2008, 10:28 am
Re: Launching: Sea Flea
Kudzu -- 6/27/2008, 8:29 am