Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Strip: few questions about milling the strips
By:ancient kayaker
Date: 11/20/2011, 9:43 am
In Response To: Re: Strip: few questions about milling the strips (Mike Bielski)

: I had a clean shop when the guy from Fine Woodworking came to
: photograph me in it for the article I wrote. Man that was a lot
: of work. When I worked in a professional shop we spend half of
: every friday cleaning. If I had half a day a week to clean my
: shop it would still look awesome, but right now most of the time
: I don't have that much time spread out over a single week,
: sometimes two.

: Of course, now everything takes twice as long because nothing is
: ever put away where it belongs...

: m

You guys need a system! It doesn't actually matter much what the system is so long as yo stick to it. My one is simple enough, nothing is ever cleaned or put away until I can't find something I need right tnow; then I start putting things away and cleaning up until I find it, then back to work.

Cleaness may be next to Godliness but there's mention of it in the Bible when Noah was building the Ark!

Messages In This Thread

Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 3:51 pm
Re: Strip: few questions about milling the strips
Donovan -- 11/18/2011, 4:07 pm
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 4:26 pm
Re: Strip: few questions about milling the strips
StephenHJ -- 11/22/2011, 12:54 pm
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/23/2011, 2:36 am
Re: Strip: few questions about milling the strips
Mike Savage -- 11/23/2011, 11:28 am
Re: Strip: few questions about milling the strips
Kevin McAtee -- 11/23/2011, 6:22 pm
Re: Strip: few questions about milling the strips *PIC*
Rick -- 11/24/2011, 2:18 pm
Re: Strip: few questions about milling the strips *PIC*
Dwight Lynn -- 11/18/2011, 6:03 pm
Re: Strip: few questions about milling the strips
Etienne Muller -- 11/18/2011, 6:15 pm
Re: Strip: few questions about milling the strips
Dwight Lynn -- 11/18/2011, 6:22 pm
Re: Strip: few questions about milling the strips
Etienne Muller -- 11/18/2011, 6:36 pm
Re: Strip: few questions about milling the strips *PIC*
Dan Caouette (CSFW) -- 11/18/2011, 6:44 pm
Re: Strip: few questions about milling the strips
Mike Bielski -- 11/19/2011, 12:00 am
Re: Strip: few questions about milling the strips
Etienne Muller -- 11/19/2011, 4:38 am
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/20/2011, 2:17 am
Re: Strip: few questions about milling the strips
Dan Caouette (CSFW) -- 11/19/2011, 5:52 am
Re: Strip: few questions about milling the strips
Mike Bielski -- 11/19/2011, 12:37 pm
Re: Strip: few questions about milling the strips
ancient kayaker -- 11/20/2011, 9:43 am
Re: Strip: few questions about milling the strips
ancient kayaker -- 11/20/2011, 9:44 am
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/21/2011, 1:27 am
Re: Strip: few questions about milling the strips
Kevin McAtee -- 11/25/2011, 8:02 pm
Re: Strip: few questions about milling the strips
ancient kayaker -- 11/25/2011, 9:01 pm
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 8:08 pm
Re: Strip: few questions about milling the strips
Clayton Plunkett -- 11/21/2011, 10:57 am
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/22/2011, 12:28 am
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/22/2011, 12:46 am
Re: Strip: few questions about milling the strips
Kevin Greer -- 11/18/2011, 7:02 pm
Re: Strip: few questions about milling the strips
Allan -- 11/18/2011, 8:46 pm
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/18/2011, 9:02 pm
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/19/2011, 2:55 am
1/4 in strips
Jay Babina -- 11/22/2011, 2:43 pm
Re: 1/4 in strips *PIC*
John Caldeira -- 11/24/2011, 2:41 am
Re: Strip: few questions about milling the strips
skrap1r0n -- 11/22/2011, 10:14 pm
Re: Strip: few questions about milling the strips
Paul G. Jacobson -- 11/22/2011, 10:50 pm
Re: Strip: few questions about milling the strips
Bill Hamm -- 11/23/2011, 2:37 am
OT: I'm back
Paul G. Jacobson -- 11/23/2011, 8:36 pm
Re: OT: I'm back
Bill Hamm -- 11/24/2011, 2:59 am
Re: OT: I'm back
ancient kayaker -- 11/24/2011, 5:56 pm
Re: OT: I'm back
Bill Hamm -- 11/26/2011, 2:23 am