Boat Building Forum

Find advice on all aspects of building your own kayak, canoe or any lightweight boats

Re: Gas mask valve
By:Mark Kanzler
Date: 9/18/1998, 7:03 pm
In Response To: Re: Gas mask valve (Nolan Penney)

You could put two one-way valves into tandem operation. One valve would allow air in, and it'd be mounted high. The other would allow air out, it'd be mounted low.

The mildew problem still will need to be addressed. A screw in hatch sounds like the way to go for that part of the problem.

> Having lived more hours in a gas mask then I care to think about, I'll
> comment here that they take no pressure to operate. They are not spring
> loaded, but are just a flapper retained against the seat by shape. If they
> get sticky from sweat or slobber, they take a faint bit of exhalation
> pressure to pop open. The human can only generate something like .4psig
> exhailing, so by faint pressure to the human, I mean very faint pressure
> overall.

> The first problem with this double valving is that it will allow water
> back in just as well air. Quicker in fact. Any water splashing aginst the
> valve would enter. Shielding it would protect it from splash, but any
> water standing against the valve would enter it. You would have to ensure
> the valve stays above water at all times to make it water tight. Something
> that isn't feasable for a kayak.

> The second problem is these valves take a set, so they quit sealing in the
> neutral position. Just like those rubber scuppers used on power boats.
> They work when their brand new too, but after a few weeks to a few months,
> their no longer seating in the neutral position. Recommended routine
> maintenance on gas masks is to replace the valves every 3 months,
> regardless of use.

Messages In This Thread

Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 4:16 pm
Everyone wants to vent
Paul Jacobson -- 9/18/1998, 4:19 am
Re: Everyone wants to vent
Rick VanBuren -- 9/18/1998, 4:38 pm
vent and w(h)ine
Paul Jacobson -- 9/19/1998, 9:26 pm
Re: Everyone wants to vent
Mike Spence -- 9/18/1998, 3:14 pm
Re: Venting - it's not a problem
Jay Babina -- 9/17/1998, 10:06 am
Re: Venting A Sealed Compartment
Pat Pavlik -- 9/16/1998, 10:56 pm
Re: Venting A Sealed Compartment
Mark Kanzler -- 9/16/1998, 4:02 pm
Re: Venting A Sealed Compartment
Jon K. -- 9/15/1998, 7:40 pm
Re: Venting A Sealed Compartment - MY SOLUTION
Jim Ward -- 9/15/1998, 8:59 pm
Re: Venting A Sealed Compartment - MY SOLUTION
Mark Kanzler -- 9/16/1998, 11:35 am
Re: Venting A Sealed Compartment - MY SOLUTION
Nolan Penney -- 9/16/1998, 8:45 am
Re: Venting A Sealed Compartment - MY SOLUTION
Scotty -- 9/16/1998, 11:28 am
Comments on Your Solution
Jon K. -- 9/15/1998, 10:49 pm
Re: No Foam. Inspection Port In Bulkhead
Jim Ward -- 9/16/1998, 10:28 pm
Re: No Foam. Inspection Port In Bulkhead
Mark Kanzler -- 9/18/1998, 5:35 pm
Re: No Foam. Inspection Port In Bulkhead
Mark Kanzler -- 9/18/1998, 5:55 pm
Re: No Foam. Inspection Port In Bulkhead
Nick Schade -- 9/17/1998, 5:01 pm
Re: PVC pipe fittings
Nolan Penney -- 9/17/1998, 8:01 am
Re: No Foam. Inspection Port In Bulkhead
Mike Spence -- 9/17/1998, 12:50 pm
Re: No Foam. Inspection Port In Bulkhead
Rick VanBuren -- 9/17/1998, 4:17 pm
Re: No Foam. Inspection Port In Bulkhead
Pat Pavlik -- 9/16/1998, 11:56 pm
Flexible inspection plate
Mike Spence -- 9/17/1998, 12:17 pm
Re: Venting A Sealed Compartment
L.C. -- 9/15/1998, 7:26 pm
Re: Venting A Sealed Compartment
Mark Kanzler -- 9/15/1998, 5:46 pm
Re: Venting A Sealed Compartment
Mark Carroll -- 9/15/1998, 4:46 pm
Re: Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 5:23 pm
Re: Venting A Sealed Compartment
Ross Leidy -- 9/15/1998, 4:34 pm
Re: Venting A Sealed Compartment
Martin Foil -- 9/16/1998, 3:10 pm
run a vent tube
Brian C. -- 9/15/1998, 5:30 pm
Re: run a vent tube
Jim Ward -- 9/15/1998, 6:19 pm
Re: run a vent tube
Rick C. -- 9/17/1998, 10:15 pm
Re: run a vent tube
Mark Kanzler -- 9/18/1998, 6:42 pm
Re: Gas mask valve
Mike Spence -- 9/18/1998, 3:01 am
Re: Gas mask valve
Mark Kanzler -- 9/18/1998, 6:55 pm
Re: Gas mask valve
Nolan Penney -- 9/18/1998, 7:01 am
Re: Gas mask valve
Mark Kanzler -- 9/18/1998, 7:03 pm
Re: Tandem valve....
Tor-Henrik Furmyr -- 9/19/1998, 6:42 pm
Re: Tandem valve....
Mark Kanzler -- 9/20/1998, 1:06 am
valveless `valve'
Paul Jacobson -- 9/19/1998, 8:44 pm
Re: Gas mask valve
Rick C. -- 9/18/1998, 2:28 pm
Re: Venting A Sealed Compartment
Jim Ward -- 9/15/1998, 5:28 pm
Re: Idea #2
Nick Schade -- 9/16/1998, 5:57 pm
Re: Venting A Sealed Compartment
Nick Schade -- 9/16/1998, 5:44 pm
Re: Venting A Sealed Compartment
Ross Leidy -- 9/15/1998, 5:52 pm